Written by
Kristen Cramer
Fact-checked by
Tom Grupa
New driveway cost
A new driveway costs$3 to $12 per square foot to install, widen, or extend. Driveway replacement costs $4 to $15 per square foot to redo when removing the old driveway. The average cost to build a 24'x24' driveway is$1,700 to $6,900for materials and installation.
Driveway prices depend on the size, material (concrete, asphalt, gravel, etc.), and if it's a new install or replacement.
| Size | Square feet | Average cost |
|---|---|---|
| 12x24 Driveway (1-Car) | 288 | $850 – $3,450 |
| 24x24 Driveway (2-Car) | 576 | $1,700 – $6,900 |
| 24x36 Driveway (3-Car) | 864 | $2,600 – $10,350 |
| 50’ Diameter circular driveway | 1,650 | $5,000 – $15,000 |
| 10x10 Driveway extension or apron | 100 | $300 – $1,200 |
Average driveway cost calculator
Enter the length and width of the driveway in feet below to estimate the cost.
Cost to build a driveway by type
The cost to build a driveway is$600 to $18,000 on average, depending on the material. The cheapest driveways cost$1 to $3 per square footfor gravel, while standard concrete and asphalt driveways cost$3 to $8 per square foot.
| Driveway material | Cost per square foot | Average total cost* |
|---|---|---|
| Concrete | $4 – $8 | $2,400 – $4,800 |
| Asphalt / Blacktop | $3 – $7 | $1,800 – $4,200 |
| Gravel | $1 – $3 | $600 – $1,800 |
| Chip Seal | $2 – $5 | $1,200 – $3,000 |
| Heated | $12 – $28 | $7,200 – $16,800 |
| Pavers | $10 – $30 | $6,000 – $18,000 |
| Permeable pavers | $8 – $30 | $4,800 – $18,000 |
| Grass pavers | $4 – $12 | $2,400 – $7,200 |
| Exposed aggregate | $5 – $11 | $3,000 – $6,600 |
| Rubber | $6 – $11 | $3,600 – $6,600 |
*Based on a 600 square foot driveway.
Concrete driveway
Installing aconcrete driveway costs$2,400 to $4,800on average or$4 to $8 per square footfor plain gray concrete. Adding decorative colors, borders, stamped patterns, and finishes costs$8 to $18 per square foot.
Concrete lasts30 to 40 yearsand handles hot climates better than asphalt.
Get free estimates from concrete driveway contractors.
Asphalt / blacktop driveway
Asphalt driveway paving costs$3 to $7 per square footor$1,800 to $4,200on average for a 600 square foot two-car driveway. Blacktop lasts15 to 30 yearsand withstands freezing temperatures better than concrete but requires sealing every3 to 5 years.
Gravel driveway
A gravel driveways costs$1 to $3 per square footinstalled or$600 to $1,800for a two-car driveway. Gravel is the cheapest driveway surface and lastsup to 100 yearswith a stable foundation and proper maintenance. Well-built gravel driveways require light raking and new gravel once or twice a year.
Gravel pricesrange from$10 to $50 per ton, depending on the stone size and type. Prices include delivery up to 10 miles.
Chip seal driveway
A chip seal driveway costs$1,200 to $3,000installed or$2 to $5 per square foot. Chip seal, also called tar and chip, lasts7 to 10 years. Tar and chip driveways come in various colors and feature layers of stone aggregate spread over hot liquid asphalt.
Heated driveway
Radiantheated driveways cost$12 to $28 per square footinstalled or$7,200 to $16,800for a two-car driveway. Heated driveways can be topped with asphalt, concrete, or pavers and cost$120 to $600 per winterto operate.
Snow melting driveway mats cost$1,600 eachto cover the tire track area only and can be rolled up and stored the rest of the year.
Concrete, brick, or cobblestone paver driveway
Driveway pavers cost$10 to $30 per square footon average installed or$6,000 to $18,000for a two-car driveway. High-end concrete block, paving stones, or brick paver driveways cost$25 to $50 per square foot. Driveway pavers last25 to 75 years, depending on maintenance and weather.
Permeable pavement
Permeable pavers cost $8 to $30 per square foot installed or $4,800 to $18,000 on average.
Porous asphalt costs $7 to $13 per square foot.
Pervious concrete costs $8 to $16 per square foot and drains faster than porous asphalt or permeable pavers.
Grass driveway cost
Grass driveway pavers cost$4 to $12 per square footor$2,400 to $7,200on average, depending on if they're concrete or plastic. Grass block pavers – also known as grow-through or turf block pavers – allow water to sink into the grid system while grass grows through the holes.
Sod installation costs$0.90 to $1.80 per square footfor a plain grass parking area. Sod is only recommended for places that get minimal traffic.
Exposed aggregate / pebble driveway
Exposed aggregate or pebble finish driveways cost$5 to $11 per square footor$3,000 to $6,600on average. Exposed aggregate features stones mixed into concrete or seeded on the surface. Natural aggregates provide a textured, nonskid surface in various colors, including pastels, earth tones, and deep reds and blues.
Rubber driveway cost
Rubber driveways cost$6 to $11 per square footinstalled or$3,600 to $6,600and are made of eco-friendly recycled rubber poured over existing concrete or asphalt. Rubber driveways are durable, weather-resistant, easy to clean and maintain, and can be customized with different colors and patterns.
Circular driveway cost
Circular driveways cost10% to 20% morethan straight driveways because building a curved shape requires more labor and installation time. Wrap-around driveways take up more yard space but add curb appeal and provide a way for vehicles to enter and exit easily.
Driveway installation cost factors
The following factors affect driveway installation costs:
Driveway size, material, and thickness have the most significant impact on the total cost.
Labor makes up 50% of the total project cost.
Designs with stamped patterns, colored stains, finishes, or stencils add $2 to $15 per square foot.
Concrete curbing costs $5 to $18 per linear foot. Curbing creates a border along the driveway to separate it from the landscaping, preventing soil from washing onto the driveway in the rain.
Borders featuring stone or brick pavers cost $10 to $25 per square foot installed.
Adding rebar or wire mesh to concrete for strength costs $1 to $3 per square foot.
Excavation costs $1 to $5 per square foot to remove plants, soil, and small trees from the driveway site.
Grading and site prep costs $5 to $8 per square foot and ensures the sub-base is stable and the driveway allows water to drain correctly. Costs increase for heavily sloped sites.
A new drainage system costs $400 to $2,400 to add trenches or channels along the driveway.
Location affects material and labor prices. Installation typically costs more in major cities with a higher cost of living. However, material delivery costs are often higher in rural areas.
Accessibility and terrain also affect the price. Driveways with landscape obstructions that make it difficult to maneuver heavy equipment cost more to install.
Adding an automatic driveway gate costs $2,000 to $5,000 on average to install.
Compare driveway installation quotes.
Search
Driveway cost per square foot
| Square feet | Average price range* |
|---|---|
| 200 | $600 – $2,400 |
| 400 | $1,200 – $4,800 |
| 600 | $1,800 – $7,200 |
| 800 | $2,400 – $9,600 |
| 1,000 | $3,000 – $12,000 |
*Based on the $3 to $12 per square foot average range.
Cost to replace or redo a driveway
Driveway replacement costs$4 to $15 per square foot, including$1 to $3 per square footto remove the old driveway and haul away the debris. The cost to redo a driveway depends on the material, site conditions, and whether the existing subbase is reusable.
| Project | Cost per square foot | Average total cost |
|---|---|---|
| Driveway replacement | $3 – $12 | $1,800 – $7,200 |
| Old driveway removal | $1 – $3 | $600 – $1,800 |
| Widen driveway | $3 – $12 | $1,800 – $7,200 |
| Driveway extension | $3 – $12 | $1,800 – $7,200 |
| Driveway resurfacing | $1 – $7 | $600 – $4,200 |
*Based on a 600 square foot driveway.
Cost to widen driveway
Widening a driveway costs$3 to $12 per square foot, depending on the materials. Adding 200 square feet of driveway surface costs$600 to $2,400on average. Minimum and maximum driveway widths may be subject to local zoning regulations.
Driveway extension cost
The cost to extend a driveway runs$3 to $12 per square foot, depending on the material and site conditions. A driveway extension may require additional excavation, a new drainage system, and a new paved apron where the driveway meets the public street.
Driveway resurfacing
Asphalt driveway resurfacing costs$1 to $3 per square foot.Concrete resurfacing costs$3 to $7 per square foot. Resurfacing involves removing the driveway's damaged top layer and overlaying it with new concrete or asphalt, which gives the look of a new driveway at a lower cost.
Driveway FAQs
What is the cheapest type of driveway?
The cheapest driveway material is gravel at$1 to $3 per square footusing aggregate made of crushed shells, crushed concrete or asphalt, or pea gravel. Tar and chip seal driveways are the second cheapest at$2 to $5 per square foot.
How long does a driveway last?
Asphalt driveways last15 to 30 years, and concrete driveways last30 to 40 years, depending on the climate and usage. Brick and stone pavers last25 to 50 years. A cobblestone or gravel driveway lastsup to 100 yearsif well-maintained.
| Driveway type | Lifespan (years) |
|---|---|
| Asphalt | 15 – 30 |
| Concrete | 30 – 40 |
| Brick/concrete pavers | 25 – 75 |
| Cobblestone | Up to 100 |
| Gravel/crushed stone | Up to 100 |
How long before you can drive on a new driveway?
Asphalt driveways take48 to 72 hoursminimum to cure. Concrete driveways take7 to 10 daysbefore the concrete cures enough to drive or park a passenger car on it. You can drive on a new gravel or paver driveway immediately after installation is complete.
When to seal a new driveway
Asphalt driveways require sealing every3 to 5 yearsand3 to 9 monthsafter any repairs, resurfacing, or repaving. Asphaltdriveway sealing costs$100 to $190, depending on the number of coats.
Concrete driveways don't require sealing, but sealers protect the surface from moisture and stains.
Do I need a permit to redo my driveway?
Adriveway permit costs$50 to $200, depending on location. Most cities require permits for new driveway installations and replacements but not for repairs. Some cities waive the permit fee if there is already a paved apron connecting the property to a public street.
Does a new driveway add value to a house?
Adding a paved driveway increases a home's value and curb appeal. If most homes in the neighborhood have gravel driveways, a paved driveway sets a house apart, increasing its value. If other homes have paved driveways, replacing a gravel driveway with concrete or asphalt increases the value.
How much does it cost to repair a driveway?
Driveway repair costs$100 to $400to fix cracks and patch potholes or$600 to $3,000for major repairs or resurfacing.
Asphalt driveway repair costs$2 to $5 per square foot.
Concrete driveway repair costs$3 to $8 per square footto fix crumbling or spalling.
Still have questions? Ask a driveway contractor.
Search
DIY driveway cost
While small driveway repairs may be suitable DIY projects, new driveway installation often involves heavy industrial machinery and requires specific skills and experience. Most installations require a team of two or more people working together. Hire a professional contractor for the best results.
Getting driveway quotes
Before hiring a driveway installer and signing a contract, be sure to:
Look for contractors experienced in installing the driveway material you selected. Most contractors specialize in only one surface material.
Ensure the estimate includes the subgrade and base, pavement thickness, overall cost by line-item, and payment schedule.
Get at least three in-person quotes to compare.
Read reviews and check out their previous work on HomeGuide and Google.
Select companies that are insured, bonded, and have been in business for 5+ years.
Avoid selecting the lowest quote as quality may suffer.
Ask for a written contract and warranty.
Get a full breakdown of all costs involved.
Avoid making large payments up front. Come up with a payment schedule instead.
Questions to ask driveway contractors
Are you licensed, insured, and bonded?
Can you provide examples or addresses of your previous driveway paving jobs?
Will you be using control joints or wooden expansion joints to minimize concrete cracking?
Does the estimate include all materials, delivery, and labor fees?
What additional costs can I expect?
What permits do I need, and will you obtain them?
What does your warranty policy include?
(Video) How much does a paver driveway cost? Learn about the different costs of paver driveways by SIZE.What is your payment schedule?
FAQs
How do you calculate the cost of a driveway? ›
A driveway costs between $1,700 to $7,000 for materials and averages $4,500. Expect to pay between $2 and $15 per square foot for materials and installation. You can save money by choosing a material that fits your budget, but each material has a different lifespan, so weigh the costs against the longevity.
What is the cheapest type of driveway? ›Gravel is the least costly material to pave a driveway. The price ranges from $1 to $3 per square foot. The average total cost is usually around $1,200, though this number may not account for the fact that gravel is usually used to pave much larger driveways as a cost-reduction solution.
Is driveway worth replacing? ›It really depends on the condition of your driveway and the market you are in. If your neighbors have pristine driveways, repairing your concrete driveway should be your top home improvement priority. A new driveway will improve your home's curb appeal and increase property value.
What is the cheapest concrete driveway? ›Standard. A standard, plain gray driveway comes to mind most often when the phrase “concrete driveway” is mentioned. It's the most economical choice for concrete driveway costs, with an average of $4 to $7 per square foot.
How much does a driveway add to property value? ›On average, you can expect a good quality driveway to add between 5% to 10% value on top of your home. That's no guarantee, however, as there are some factors that can determine whether or not you need off-street parking at all.
Is asphalt or concrete better for driveway? ›Overall, the difference between asphalt and concrete driveways is that asphalt is less durable than concrete. With proper maintenance, it can last 30 years. Alternatively, concrete provides a sturdy, long-lasting option and can last homeowners 50+ years with occasional repairs and degreasing.
What is the best driveway option? ›Concrete is the most popular driveway material, and for good reason. Durable and low-maintenance, you won't have to give much thought to a concrete driveway. It may not earn as many compliments as upscale alternatives, but concrete is a dependably solid choice with a mid-range price.
What type of driveway lasts the longest? ›Concrete, cobblestone, asphalt, brick, and interlocking pavers are the most durable driveway installation options available today. Apart from their lengthy lifespans, these materials also hold up well in any climate, require minimal maintenance, offer a smooth drive, and elevate your home's first impression.
What type of driveway adds most value? ›Why Is An Asphalt Driveway The Best Option? Pound for pound, asphalt is the building material that gives you the most bang for your buck. Concrete can cost $6.00 to $10.00 per square foot whereas the price of asphalt typically ranges between $4.00 to $6.00 per square foot.
How often do driveways need to be replaced? ›Typically you'll need to replace an asphalt driveway after 20 years and a concrete drive after 25 years. Repairing a driveway nearing this age is not considered a wise investment. Beyond the condition of your driveway, many old driveways could do with an update just as a home benefits from renovations.
How often should you redo your driveway? ›
In general, you should plan on replacing your asphalt driveway every 20 years. But how long your driveway lasts will depend on how much maintenance it's received over the years as well as the conditions it's endured. For example, you may have to replace your driveway sooner if you didn't invest in sealcoating.
How long should you stay off a new driveway? ›Wait at least 3 full days before allowing traffic on the new asphalt. Since asphalt needs time to harden and cure, usually 6-12 months, your parking lot or driveway will remain soft and pliable until then.
Is a new concrete driveway worth it? ›Even though concrete driveways cost a little more upfront, the longevity and low maintenance of concrete are well worth the extra cost. If properly sealed every couple of years, it should hold up and not have to be replaced until at least 25 years, some holding steady until 50 years.
Is 4 inches of concrete enough for a driveway? ›As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
How big is the average driveway? ›| Type | Size (in feet) |
|---|---|
| Individual Car Driveway Width | 10-12' wide |
| Double Car Driveway Width | 20-24' wide |
| Parking Space Dimensions Per Car | 10'W x 22'L |
| Individual Car Turn-around Dimensions | 10'W x 20'L |
One of the best ways to save money is to use loose materials such as gravel, stone, or tar-and-chip (macadam) for your driveway surface.
Does a new paved driveway add value? ›Most homeowners who want to improve their property's value include paving the driveway on their checklist. And that's not surprising. A paved asphalt driveway can be done quickly to increase curb appeal and, in turn, increases the house's market value.
Does a big driveway add value? ›According to Price Your Job, a house can increase in value anywhere from 2-10% with the addition of a driveway. The value that a driveway can add to your home will depend on the location, size and quality, and also how well it matches with your home and the surrounding neighbourhood.
What is the best low maintenance driveway? ›- Paving Stones. Paving stones are known to last up to a full century if properly laid. ...
- Concrete Grass Pavers. An interlocking concrete grass paver driveway made may be an option for your driveway. ...
- Plastic Permeable Pavers.
While concrete driveways are more expensive initially than asphalt ones, they're cheaper in the long run due to their lifespan. Concrete driveways require little upkeep and will last for years. Longer lifespan especially with proper maintenance.
How many years does an asphalt driveway last? ›
The life expectancy varies based on climate, traffic, and maintenance. It is possible to have asphalt pavement last 25-30 years, but this depends on how strong the base is, the soil types underneath, how well those soils drain, how think the original road, parking lot, or drivewaywas paved.
What is the easiest driveway to install? ›1. Asphalt Driveway. Asphalt driveways are the least expensive of all driveways, and they also don't need as much maintenance as other materials. These driveways are especially preferred for commercial remodeling projects because the material is easier to pour.
What is the strongest driveway? ›Concrete. Among the most durable options on the market is a concrete driveway surface. Although it provides a hard and stable surface, that is highly dependant on professional installation, high upfront costs, maintenance, and weather conditions.
Does a driveway increase home value? ›“A [concrete] driveway can increase your property's value between 5 and 10 percent” says Fast Sales Homes. That means “a $500,000 home can increase to a $550,000 home.” On average, a new 2-car concrete driveway costs anywhere from $3-$6,000, which makes this type of an investment pretty significant.
Which is better blacktop or asphalt? ›Blacktop is heated to approximately 150 degrees celsius, whereas asphalt is only heated to 120 degrees celsius. Asphalt is has a higher bitumen content and for that reason is less porous and more resilient to wear and tear from high traffic and thus is the preferred choice for major highways.
How much does it cost to pour a long driveway? ›Installing a concrete driveway typically costs $4 to $15 per square foot. Expect to pay more for a large, long driveway, especially if it has a unique shape. This project generally ranges from $2,340 to $7,500 (including removing existing concrete) but can go as high as $10,000 or more.
What is the best way to replace a driveway? ›- Gravel: This surface is the easiest for a DIYer to achieve, and is the cheapest option too. ...
- Paving Stones: Paving stones can include concrete stones, paving stones and bricks. ...
- Asphalt Or Concrete: ...
- Resin Bound Surfacing:
Concrete is a hard-wearing, long-lasting driveway materials choice and can be finished in a surprising number of ways, as the poured variety can be stamped with patterns. Concrete has a very long lifespan of four decades or more.
What is the strongest concrete for a driveway? ›Generally, the best concrete mix for your driveway should have a compressive strength of at least 3500 psi to 4000 psi, a cement-water ratio of around 0.50 to improve the concrete's longevity, and aggregates no larger than 1-inch in size with a slump of 4 to 5 inches.
Does asphalt driveway decrease property value? ›Asphalt driveways can last you 20-25 years if properly installed and maintained – a great investment. One final point about paved driveways. While they increase the value of your home, a nice paved driveway can also help sell your home FASTER.
What should you not do on a new driveway? ›
Avoid driving on new asphalt initially.
You may drive over your driveway after 2 days, but do not park on it for 5 days and possibly longer in hotter temperatures. Even after the blacktop has cured, do not expect it to be as hard as concrete. Your new blacktop will soften and harden as temperatures rise and fall.
In general, you can expect new asphalt to take anywhere from 48-72 hours to dry completely. However, if the weather is particularly humid or cold, it may take up to a week for the asphalt to fully cure.
How do I know when my driveway needs replacing? ›- Cracks. Cracks are known to form on concrete and asphalt driveways over time. ...
- Potholes. Potholes can be dangerous for your car and other vehicles that enter your driveway. ...
- Drainage Problems. ...
- A Rough Look. ...
- An Old Driveway.
Industry standards recommend that you wait one year or go through one winter before you seal coat a new driveway. How often should I seal coat my driveway? Industry standards recommend every two years; allowing the sealer to wear away before you reseal the driveway.
How long should a driveway be for 2 cars? ›Generally plan your driveways using 18-20 feet of length for each car or truck. Allow 22-24 feet for full size pickups with extended cabs and oversized mini-vans. Allow walk around room at the bottom of the drive of 3-5ft if you have the space.
How long does a driveway take to complete? ›Typical concrete projects for residential use normally take 1-3 days. Curing time adds to the time required before new concrete can be used. To understand this better, you first need to understand the process of concrete driveway paving.
How long before you can park on new concrete driveway? ›How Long Before I Can Park On My New Driveway? For Concrete: You may drive and park your personal vehicle on your new concrete surface after 7 days. Your new concrete is designed to reach 90% of its full strength potential after 7 days, so feel free to drive your personal vehicle on it then.
Can you pour new concrete over old concrete driveway? ›Yes, you can pour fresh concrete over existing concrete. As long as your concrete is in mint condition, this task is doable. If you decide to pour a new mixture over an old slab, be sure it is at least 2 inches thick.
Is it cheaper to concrete or pave? ›Asphalt paving tends to be cheaper than concrete, with a concrete driveway costing almost double the price of an asphalt one. However, when looking at costs in the long run, concrete will end up saving you the most money.
Should I use concrete or cement for driveway? ›Concrete is a favored material for driveways, and for good reason. Concrete slabs are very strong and durable, and they require very little maintenance. The combined strength and longevity make concrete a relatively good value for large areas of paving.
Do you need gravel under concrete driveway? ›
Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab. Adding a layer of crushed stone will add proper drainage, as well as create a barrier between your slab and the ground.
Does a driveway need rebar? ›Rebar & wire mesh reinforcement
Using steel reinforcement will provide additional structural capacity for your driveway and is especially important if the slab will be exposed to heavy traffic. Reinforcement won't prevent cracks, but it will help hold them together if they do occur.
Residential Driveway: Standard Concrete Driveway Thickness
The minimum thickness for a residential concrete driveway is 4 inches. However, 5 or 6 inches is recommended if you live in an area with heavy traffic or large vehicles. For extra strength and durability, you can go up to 8 inches.
Measure the length and width of the new driveway in feet. Multiply these two numbers together to find the total square footage of the area. For example, a 20- by 40-foot driveway has a total surface area of 800 square feet.
How do you calculate a driveway? ›Calculating the area of the driveway
You will need to multiply the length of the area and width; this will give you the total area. An example of this is if your driveway is 15m long and just 3m wide then your driveway area is 45m sq.
Size: The average 2-car driveway in the U.S. is 16 x 40 feet, or a total of 640 square feet. Many driveways may be larger or smaller, depending on the distance from the garage or house to the street and possible extensions for RV parking.
How do you calculate the cost of an asphalt driveway? ›Asphalt is usually priced by square foot. The cost per ton is $40 to $80 and per square foot is $0.75 to $2.00. The cost is determined by the size of rock in the asphalt, volume ordered, delivery cost, and the location of the work being performed.
How to calculate concrete for driveway calculator? ›formula for concrete: total concrete volume = length×width×depth . Our example calculation gives 60m³ of total concrete volume. formula for gravel: total gravel volume = length × width × gravel_depth .
Is 2 inches of asphalt enough for a driveway? ›Residential driveways typically use 2 to 3 inches of asphalt with 3 being suitable for occasional large trucks or heavy equipment. Underneath the asphalt you should have 6 to 8 inches of granular base aggregate.
How much does 1 ton of asphalt cover? ›One ton of asphalt covers:
½” or 12.7 mm thick = 95 SqM. 1” or 25.4 mm thick = 48 SqM.
What is the cheapest asphalt for driveway? ›
Recycled or Reclaimed Asphalt Costs
Recycled asphalt is an eco-friendly choice that can be much more affordable than new asphalt. On average, you'll pay $10 to $20 per ton or $0.20 to $0.75 per square foot for recycled asphalt material and $5 to $7 per square foot for labor.
A concrete driveway costs from $8 to $18 per square foot, depending on decorative colors and finishes. While a plain gray concrete driveway costs between $5 and $7 per square foot to install.
How many inches deep should a concrete driveway be? ›As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
Is 2 inches of concrete enough for a driveway? ›Residential Driveway: Standard Concrete Driveway Thickness
The minimum thickness for a residential concrete driveway is 4 inches. However, 5 or 6 inches is recommended if you live in an area with heavy traffic or large vehicles. For extra strength and durability, you can go up to 8 inches.
Thickness is the major factor (even more than the strength of the concrete) in determining a driveway's structural capacity. Place concrete at a minimum thickness of 4 inches.
How wide is a normal driveway? ›How Wide Are Residential Driveways? Primarily, most professionals recommend that you install a 10 feet to 12 feet wide driveway. The standard driveway width for an SUV or conventional pickup truck is 10 feet.
How much is 1 yard of concrete? ›Concrete is priced at $125 per cubic yard on average, with prices ranging from $110 to $165 per cubic yard nationwide. Need concrete poured for a home improvement project? The typical cost of concrete is between $110 and $165 per cubic yard on average (excluding labor cost).
How thick should an asphalt driveway be? ›A 4-inch thickness may be adequate, but 5 or even 6 inches of full-depth asphalt will assure you of a stronger, stable driveway under a wider range of climate and loads. As an option, some contractors use 6 to 8 inches of compacted aggregate, or gravel, as a base under 3 inches of asphalt pavement.
How long does asphalt last? ›The lifespan of asphalt pavement depends on a number of factors. The most critical element in extending the life of asphalt pavement is proper maintenance and upkeep. Properly maintained asphalt pavement should last between 20 and 30 years, or 25 years on average.
How many layers of blacktop are on a road? ›Typical asphalt pavements consist of two or three asphalt layers which are installed successively. Construction and road closure times could be reduced, if those layers were built simultaneously.